How To Remove A Bent Screw

1
Switch screwdrivers. When a screw is stripped, attempt to remove it with a different screwdriver.
- Get-go, endeavor using a shorter screw driver with a larger head. Apply downwardly pressure and slowly attempt to remove the screw.
Tip: If this doesn't piece of work, endeavour using a screwdriver with a different type of caput. For example, if the screw is a philips head, attempt a flathead screwdriver intead. When using a flathead screwdriver, it must be narrow enough to fit inside the unabridged hole. Apply downwards force per unit area and try to excerpt the screw.^[1]
2
Tap the screwdriver into the head with a hammer. Identify your screwdriver into the head. Grab a hammer and tap the base of operations of the screwdriver. This will lodge your screwdriver into the head, providing you with more than grip. Set up down the hammer and attempt to remove the spiral.^[2]
- This method works best with soft-metal screws.
Advertisement
3

Remove the screw with a pair of pliers. If there is a slight gap between the surface and the caput of the spiral, try rotating the screw out with a pair of pliers, vise (American English) or vice (British English) grips. Secure the screw within the mouth of the locking pliers. Rotate the pliers and try to turn the stuck spiral out.^[3]
iv

Drill a small hole into the caput with an electric drill. ^[4] Select the correct drill scrap and ability up your electric screwdriver. Carefully drill a small, shallow hole into the head. This volition allow your screwdriver to sit deeper in the head of the screw. Think your screwdriver and insert information technology into the head. Use down force equally yous attempt to remove the screw.^[5]
five

Employ a Dremel. Attach a metal cutting disc to the Dremel, or small electronic rotator. Ability up the tool and cut a new notch in the screw head. Take hold of a flathead screwdriver and put it in the newly cutting slot. Rotate the screwdriver and try to remove the striped screw.^[vi]

Advertisement

ane
Drill a pilot hole in the head. Use an electric drill to create a ⅛ inch hole in the center of the caput. Increase the size of the drill bit past ane/16 inch and brand the hole larger. Keep to increase the size of the drill bit by 1/16 and enlarge the hole until it is the bore of the screw extractor. Proceed the drill in the eye of the screw.^[vii]
- Annotation the recommended depth for you specific screw extractor. Don't brand the hole deeper than recommended.
2

Insert the extractor. ^[eight] Insert the extractor into the hole yous created. Lightly tap it into the screw with a hammer—brand certain the extractor's threads grip the sides of the screw before proceeding. Locate a T handle—it likely came in your extractor kit—and attach it to the top of the extractor.^[9]
3

Turn and remove the screw. Keep the extractor straight while turning information technology counter-clockwise. Avoid applying whatever lateral force per unit area to the extractor as this can cause it to bend. Go along turning the screw until information technology loosens. Pull up on the extractor to bring the screw to the surface. Pull the screw from the surface with a pair of pliers.^[10]

Advertisement

1

Use a rubber ring. To improve your screwdriver'south grip on the caput, insert a broad rubber ring between the screwdriver and the screw head. Place the safe band flat against the head and insert your screwdriver. Slowly turn the screw driver and attempt to remove the screw.^[11]
ii

Use steel wool. When you can't find a rubber ring, y'all can substitute steel wool. Identify the steel wool on top of the caput. Insert your screwdriver firmly into the hole. Rotate the screwdriver slowly and endeavour to remove the screw.^[12]
three
Apply a lubricant. Spray the spiral head with a rust penetrant. Allow the rust penetrant to sit for 15 minutes. Reapply the rust penetrant. Tap the stripped head five to half dozen times with a hammer. Recall your screwdriver and attempt to remove the screw. ^[13]
- If you are unable to remove the stuck screw, utilise a valve grinding compound. This product contains grit that will allow your screwdriver to grip the head. Insert your screwdriver into the head and endeavour removing the screw.
Advertising

1

Gather the supplies. Even if you are not a skilled welder, it is possible to adhere a nut to the stripped screw head. Purchase a super strong welding adhesive. Find a nut that is the same diameter every bit the screw head.^[14]
ii

Attach the nut to the head. Place the nut on the spiral head, making sure information technology is centered. Carefully fill the nut with the super strong welding agglutinative. Permit the product to dry the recommended amount of time.^[15]
three

Remove the screw. Brand sure the nut has completely adhered to the spiral. Grab a socket wrench and place information technology on the nut. Rotate the socket wrench and remove the stripped spiral from the surface.^[16]

Advertisement

Add New Question

Question

How practice you lot unscrew a broken screw?

Barry Zakar is a professional handyman and the founder of Petty Ruby Truck Home Services based in the San Francisco Bay Area. With over x years of experience, Barry specializes in a variety of carpentry projects. He is skilled at constructing decks, railings, fences, gates, and various pieces of furniture. Barry also holds his MBA from John F. Kennedy University.

I suggest trying to drill information technology out. If that doesn't piece of work, put in a new screw and patch the pigsty where the onetime screw was.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertizing

Endeavour wrapping a rubber/elastic band around the screwdriver. This can meliorate your grip as yous twist the screwdriver.

About This Article

Commodity Summary X

To remove a stuck screw, place a safety band or a piece of steel wool on elevation of the screw head before y'all endeavour unscrewing it, which will requite the screwdriver something to grip onto. Y'all tin also tap the screwdriver into the screw head so information technology has a better grip. If that doesn't help, effort grabbing onto the screw head with a pair of pliers and and then twisting the spiral out. To learn other ways yous can remove a stuck screw, like drilling a small hole in the screw head, scroll down!

Did this summary help y'all?

Thank you to all authors for creating a page that has been read one,214,263 times.

Did this article help you?